1922 Stanley Steamer Model 740 Information and History

View more photos
Roadster
Chassis Num: 22249

F.E. and F.O. Stanley were the world's largest manufacturers of steam cars. Their iconic Stanley is the 'coffin nose' non-condensing steamer that was introduced in 1904. Over the next decade, the car was continually improved. By the 1910s, the car had become anachronistic and its 30-50 mile range between fill-ups was less than ideal. Rival steam manufacturers were getting vastly extended range by recycling spent steam into water.

For 1915, Stanley introduced a new condensing car, the Model 720. The condenser was a radiator opening over a different temperature range. It was placed in a conventional location resulting in a look much like an internal combustion car.

In the years that followed, changes to the car included left-hand drive and the replacement of the wooden chassis frame by pressed steel. Full-elliptic springs were retained in the rear, though changes to the front included semi-elliptic springs.

The condenser allowed the car to travel upwards of 100 miles if the temperature outside was just right. The weight of the car had increased even though the powerplant was no larger. As a result, performance suffered slightly. In May of 1922, the Stanley Model 740 was introduced which addressed some of these shortcomings. It had a larger boiler, which increased the heating surface by a third and water capacity by 50 percent. The Model 740 had larger brakes and a sturdier rear axle.

This vehicle is a Model 740E Roadster. It was given a restoration in the mid-1980s and still shows well in modern times. It is painted in Brewster Green with Apple Green striping, black fenders, and a black canvas top. The interior is black leather with black carpeting and correct gray linoleum Stanley floorboards trimmed with aluminum. The odometer reads 21,436 miles.

In 1985, the car was purchased by Dr. Atwood at an Owls Head Transportation auction in Maine, and was formerly owned by Richard Riley of Hookset, New Hampshire. Other prior owners include J.H. Babcock and James Weidenhammer of Poughkeepsie, New York.

In 2009, this Model 740E Roadster was offered for sale at the Automobiles of Arizona auction presented by RM Auctions. The lot was estimated to sell for $70,000 - $90,000. As bidding came to a close, the lot had been sold for the sum of $74,250 including buyer's premium.

The Stanely Motor Carriage Company produced steam powered automobiles during the early 1900's. The automobile had just been created and many individuals and companies were experimenting with a wide variety of fuel sources, such as gasoline, electric, and steam. These three sources were the primary sources with each having benefits and limitations. The electric vehicles were limited on their range but they were clean, quiet and easy to start. The steam powered vehicles were also clean and quiet but they required a few minutes before starting to allow steam to form. The gasoline engine was noisy, dirty, and hard to start but showed the most potential. The advent of the electric starter around 1914 meant the demise of the other fuel sources.

Twins Francis Edgar and Freelan O. Stanley were born in 1849. Francis passed away in 1918 and Freelan survived until 1940. Their first glimpse of business ingenuity was shown at an early age when they opened a photographic dry plate business which they eventually sold to Eastman Kodak. They became interested in the horseless carriage and in 1897 had created their first automobile. The eventually sold the rights of their design to Locomobile.

The brothers produced steam powered vehicles from 1902 through 1917, known as the Stanley Steamers. Throughout the years the configuration of the vehicles, the complexity of the engines, and the mechanical components were all greatly improved.

The cars were simple yet complex, and rather ingenious. The frame was constructed of tubular steel and suspended by full-elliptic springs. Wooden bodies were built atop of the frames with a boiler mounted beneath the seat. A petroleum burner, later replaced by kerosene, was placed underneath the vertical fire-tube boiler and generated the steam. Piano-wire was used to reinforce the enclosure. By using piano wire, a low overall weight was maintained while increasing the structural rigidity of the boiler. The vertical fire-tubes were made of copper and later replaced with welded steel. A thick chain was connected from the engine crankshaft to a rear-mounted differential.

The boilers were made safe by incorporating certain safety valves that could be used to release pressure. Even with these safety valves, there was still concern of the boiler shell bursting. The boiler was made up of many joints and in the cases of excessive pressure, these joints would fail and release that pressure, extinguishing the burner, and subside the potential catastrophe.

The name 'coffin bonnet' was coined when the broiler was moved to the front of the vehicle, creating an appearance similar to other cars of the era. By moving it to the front of the vehicle, the noise generated by the boiling steam was slightly subsided for the passengers.

By 1917 the Stanley brothers sold their company to Prescott Warren who continued to build the steam powered car until 1927. The demise of the company was slow but much anticipated. The automobile was rapidly evolving while the Steamer was stagnate. Gasoline was inexpensive and reliable and more importantly, cheap. Steam powered cars sold for around $4000 while the Ford and Chevrolet, to name a few, were producing cars under $1000. Gasoline engines were increasing in size, capacity, and output while the steam cars hovered around 20 horsepower.

One of the most famous Steam powered cars is the Stanley Rocket which captured a land speed record for steam at 127.7 mph at the Daytona Beach Road Course. Driven by Fred Marriott, he easily secured the Dewar International Trophy awarded to the vehicle with the fastest measured mile time, which he accomplished in just 28.5 seconds.

The Stanley Rocket was designed to have limited drag. It was similar in shape to a canoe. It was long and narrow, at 16 feet long and 3 feet wide at its widest point. Most of the components of the car were housed within the body which increased aerodynamics. The 3.1 liter engine was a twin-piston double acting type that was capable of producing a reported 275 or 1000 psi at 700 degrees F. The entire vehicle weighed less than 1680 pounds.

Vehicle Spotlight

Other models by Stanley