|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
The 365 GT 2+2 came as a replacement for the 330 GT 2+2. It was debuted at the 1967 Paris Auto Salon. The design was done by Pininfarina. This was Ferrari's largest vehicle to date. It included amenities such as power windows, brakes and steering, air conditioning, pleated leather upholstery, and a radio. This was a very luxurious vehicle by Ferrari's standards.
The vehicle came equipped with the signature Ferrari V-12 producing 320 horsepower. A 5-speed manual gearbox was mounted in the rear-transaxle.
Production continued until 1971 with about 800 examples being produced.
The vehicle came equipped with the signature Ferrari V-12 producing 320 horsepower. A 5-speed manual gearbox was mounted in the rear-transaxle.
Production continued until 1971 with about 800 examples being produced.
| Designer: Pininfarina |
| Designer: Pininfarina Chassis Num: 13041 |
The 330GT 2+2 was introduced in January of 1964 and featured a steel tube chassis that had grown in length by two-inches over its predecessor, the 250GTE. Four-seater Ferrari's had grown in popularity during the mid-1960s, accounting for 50-percent of all Ferraris produced during that time. The 330 had an independent front suspension and a live rear axle. The coachwork was handled by the legendary firm, Pininfarina. Power came from a 4-liter twelve-cylinder engine that produced an impressive 300 horsepower. The gearbox was a four-speed unit with overdrive.
The 365GT 2+2 made its debut at the Paris Salon in 1967. Design cues were borrowed from the limited edition 500 Superfast and based on the contemporary 330GTC. The 365GT produced 320 horsepower from the 4.4-liter engine. Zero-to-sixty took only seven seconds with top speed being achieved at 150 mph. There were a total of 800 examples produced, with production concluding in 1971.
This 1970 Ferrari 365GT 2+2 Berlinetta was sold for $117,000 at auction, surpassing the cars estimated value.
The 365 Series were introduced in the late 1960's and stayed in production until the early 1970's. The 365's were often powered by a Columbo SOHC 4390 cc V-12 engine with three Weber carburetors capable of producing around 300 horsepower. The front and rear suspension for most of the series was independent with double wishbones and coil springs. The 365 GT4 2+2 had an independent with transverse parallelograms and coil springs suspension. The 365 California had a live axle with coil springs rear suspension. The chassis was an oval tube ladder type frame layout.
Disc brakes were standard on all the vehicles, as was the five-speed manual gearbox. Many of the series received standard options such as power steering and air conditioning, uncommon at the time. When most manufacturers such as Lamborghini and DeTomaso were creating vehicles with mid-engined design, Ferrari continued to use their tried-and-true front-engined, rear wheel design.
In 1967 Ferrari dominated the Daytona 24 Hours race with a first, second, and third place finish. At the 1968 Paris Auto Show the public and press were expecting Ferrari's new berlinetta to be dubbed 'Daytona'. They were proven wrong when Ferrari dubbed the vehicle the 365 GTB/4, however, the name Daytona is a common reference to the vehicle even to this day. Ferrari had intended on using 'Daytona' but it was revealed prematurely so the traditional Ferrari naming sequence was used.
During its production lifespan lasting from 1968 through 1974, 1383 examples of the Pinifarina designed 365 GTB/4 Daytona vehicles were created.
The famous coachbuilder Pininfarina was tasked with creating many of the designs for the 365 Series. The designs were not new, rather they borrowed many of the styling cues of the prior 330 GTC and 275 GTS models. The headlights were courtesy of the 500 Superfast. The result was a visually stunning automobile with proven Ferrari mechanics and performance.
GT represented Gran Turismo. GTB represented Berlinetta or coupe. GTS stood for open models which were either a targa roof or a full convertible. '4' represented four-cam engines. 'C' represented 'Competizione' or 'Corsa' meaning 'to race'.
365 California
In 1966 Ferrari introduced the 365 California at the Geneva Auto Show as a replacement for the Ferrari 500 Superfast. The famous coachbuilder, Pininfarina, had been tasked with creating the body for the vehicle. The result was a two door, two-seat, convertible. The 365 borrowed many of the mechanics of its predecessor including the five-speed manual gearbox, chassis, and suspension. The front of vehicle was similar in design to the 500 with the remaining portions all new. With a top speed of 240 km/h, it was the fastest convertible in the world at the time. Disc brakes provided excellent stopping power for the 1300 kg vehicle. Production continued for only a year with a total of fourteen examples being created.
365 GT2+2
In 1967 Ferrari introduced the 365 GT2+2, only its second production four-seater vehicle. The vehicle would stay in production until 1971 during which around 800 examples being created.
The rear passengers had limited headroom but there was sufficient legroom for most passengers. The purpose of the vehicle was to provided performance and comfort. As a result the vehicle was outfitted with electric windows, leather interior, power assisted brakes, full carpeting, and optional air conditioning.
365 GTC
Near the close of 1968, Ferrari introduced the 365 GTC which stayed in production until 1970. During the production lifespan, 168 examples were produced. The 365 GTC was basically a 330 GTC with a SOHC 4390 cc V-12 engine. Visually, the vehicle was very similar to its predecessor except for the air vents in the front wings had been removed. In their place were black vents placed in the back corners of the hood.
365 GTS
The 365 GTS was a replacement for the 330 GTS. It featured a 4390 cc SOHC engine and had its cooling vents removed in favor of vents in the hood. Only twenty examples were created.
365 GTC/4
In 1971 Ferrari introduced the 365 GTC/4 as a replacement for the 365 GT 2+2. It sat atop a Daytona chassis and given an independent suspension. The same Daytona ventilated disc brakes were used. The gearbox was mounted in the front and the engine was the 4390 cc V12 but with six sidedraught Weber carburetors and wet sump lubrication resulting in 340 horsepower.
The design was once again handled by Pininfarina. The two-door, 2+2 coupe had pop-up headlights and five-spoke alloy wheels. During its production lifespan lasting until 1972, around 500 examples were produced. Strict American safety and emission regulations were partly responsible for the demise of the GTC/4.
365 GT4 2+2
The 365 GT4 2+2 was debuted to the public at the 1972 Paris Auto Show as a replacement for the 365 GT 2+2 and the 365 GTC/4. It sat atop an enlarged 365 GTC/4 chassis and given the same mechanics. The larger chassis meant more interior room for the passengers, especially the rear passengers, and their luggage. The styling was once again assigned to Pininfarina. The design was different from the prior 365 models.
During its production lifespan lasting until 1976, around 470 examples were created.
365 GT4 BB
The 365 GT4 BB, meaning Berlinetta Boxer, was introduced to the public at the 1971 Turin Auto Show. Its styling was similar to the P6 show car built in 1968. The engine was a flat-12 cylinder power-plant mounted longitudinal. The gearbox was mounted under the engine. This was a great design but ultimately created an unbalanced weight distribution with most of the weight over the rear axle. The weight distribution problem and the fact that the engine was mounted high in the vehicle resulted in a car that had poor handling and never achieved successful racing status.
The 365 GT4 BB was replaced by the 512 BB in 1976. The 512 BB was similar in design but featured a five-liter engine.
Disc brakes were standard on all the vehicles, as was the five-speed manual gearbox. Many of the series received standard options such as power steering and air conditioning, uncommon at the time. When most manufacturers such as Lamborghini and DeTomaso were creating vehicles with mid-engined design, Ferrari continued to use their tried-and-true front-engined, rear wheel design.
In 1967 Ferrari dominated the Daytona 24 Hours race with a first, second, and third place finish. At the 1968 Paris Auto Show the public and press were expecting Ferrari's new berlinetta to be dubbed 'Daytona'. They were proven wrong when Ferrari dubbed the vehicle the 365 GTB/4, however, the name Daytona is a common reference to the vehicle even to this day. Ferrari had intended on using 'Daytona' but it was revealed prematurely so the traditional Ferrari naming sequence was used.
During its production lifespan lasting from 1968 through 1974, 1383 examples of the Pinifarina designed 365 GTB/4 Daytona vehicles were created.
The famous coachbuilder Pininfarina was tasked with creating many of the designs for the 365 Series. The designs were not new, rather they borrowed many of the styling cues of the prior 330 GTC and 275 GTS models. The headlights were courtesy of the 500 Superfast. The result was a visually stunning automobile with proven Ferrari mechanics and performance.
GT represented Gran Turismo. GTB represented Berlinetta or coupe. GTS stood for open models which were either a targa roof or a full convertible. '4' represented four-cam engines. 'C' represented 'Competizione' or 'Corsa' meaning 'to race'.
365 California
In 1966 Ferrari introduced the 365 California at the Geneva Auto Show as a replacement for the Ferrari 500 Superfast. The famous coachbuilder, Pininfarina, had been tasked with creating the body for the vehicle. The result was a two door, two-seat, convertible. The 365 borrowed many of the mechanics of its predecessor including the five-speed manual gearbox, chassis, and suspension. The front of vehicle was similar in design to the 500 with the remaining portions all new. With a top speed of 240 km/h, it was the fastest convertible in the world at the time. Disc brakes provided excellent stopping power for the 1300 kg vehicle. Production continued for only a year with a total of fourteen examples being created.
365 GT2+2
In 1967 Ferrari introduced the 365 GT2+2, only its second production four-seater vehicle. The vehicle would stay in production until 1971 during which around 800 examples being created.
The rear passengers had limited headroom but there was sufficient legroom for most passengers. The purpose of the vehicle was to provided performance and comfort. As a result the vehicle was outfitted with electric windows, leather interior, power assisted brakes, full carpeting, and optional air conditioning.
365 GTC
Near the close of 1968, Ferrari introduced the 365 GTC which stayed in production until 1970. During the production lifespan, 168 examples were produced. The 365 GTC was basically a 330 GTC with a SOHC 4390 cc V-12 engine. Visually, the vehicle was very similar to its predecessor except for the air vents in the front wings had been removed. In their place were black vents placed in the back corners of the hood.
365 GTS
The 365 GTS was a replacement for the 330 GTS. It featured a 4390 cc SOHC engine and had its cooling vents removed in favor of vents in the hood. Only twenty examples were created.
365 GTC/4
In 1971 Ferrari introduced the 365 GTC/4 as a replacement for the 365 GT 2+2. It sat atop a Daytona chassis and given an independent suspension. The same Daytona ventilated disc brakes were used. The gearbox was mounted in the front and the engine was the 4390 cc V12 but with six sidedraught Weber carburetors and wet sump lubrication resulting in 340 horsepower.
The design was once again handled by Pininfarina. The two-door, 2+2 coupe had pop-up headlights and five-spoke alloy wheels. During its production lifespan lasting until 1972, around 500 examples were produced. Strict American safety and emission regulations were partly responsible for the demise of the GTC/4.
365 GT4 2+2
The 365 GT4 2+2 was debuted to the public at the 1972 Paris Auto Show as a replacement for the 365 GT 2+2 and the 365 GTC/4. It sat atop an enlarged 365 GTC/4 chassis and given the same mechanics. The larger chassis meant more interior room for the passengers, especially the rear passengers, and their luggage. The styling was once again assigned to Pininfarina. The design was different from the prior 365 models.
During its production lifespan lasting until 1976, around 470 examples were created.
365 GT4 BB
The 365 GT4 BB, meaning Berlinetta Boxer, was introduced to the public at the 1971 Turin Auto Show. Its styling was similar to the P6 show car built in 1968. The engine was a flat-12 cylinder power-plant mounted longitudinal. The gearbox was mounted under the engine. This was a great design but ultimately created an unbalanced weight distribution with most of the weight over the rear axle. The weight distribution problem and the fact that the engine was mounted high in the vehicle resulted in a car that had poor handling and never achieved successful racing status.
The 365 GT4 BB was replaced by the 512 BB in 1976. The 512 BB was similar in design but featured a five-liter engine.
| Ferrari: 1960-1970 |
| Similar Automakers |
| Add Review |
| Other models by Ferrari |
 |
| 1970 Ferrari models |
| Ferrari 365 GTB/4 Competizione |
| Ferrari 512 M |
| Ferrari 512 S |
| Ferrari Dino 246 GT | 1970 Ferrari Concepts |
| Ferrari 512 S Modulo |
| Other Model Years |
| 1969 365 GT 2+2 |
| Vehicle Spotlight | ||
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  | |
Site Map
| Contact
| About Us
| Terms Of Use | Links | 
subscribe - RSS
Automobile information, history, and statistics from concept to production. | © 1998-2009 Conceptcarz.com
subscribe - RSS
Automobile information, history, and statistics from concept to production. | © 1998-2009 Conceptcarz.com