| Component | WHEELS:RIM |
|---|---|
| Manufacturer | CHRYSLER CORPORATION |
| NHTSA Campaign ID | 69V159000 |
| Notes | POSSIBILITY THAT WHEEL WELDS WERE INADEQUATE, WHICH COULD CAUSE SEPARATION FROMWHEEL DISC.(COR- RECT BY INSPECTING AND CHANGE WHEELS WHERE NECESSARY.) |
| Component | POWER TRAIN:AXLE ASSEMBLY |
|---|---|
| Manufacturer | CHRYSLER CORPORATION |
| NHTSA Campaign ID | 69V164000 |
| Notes | POSSIBILITY THAT INCORRECT AXLE WAS INSTALLED DURING ASSEMBLY.(CORRECT BYINSTALLING PROPER AXLE TO MATCH OTHER OPTIONAL EQUIPMENT). |
| Component | SEATS:FRONT ASSEMBLY:RECLINER |
|---|---|
| Manufacturer | CHRYSLER CORPORATION |
| NHTSA Campaign ID | 71V070000 |
| Notes | CHRYSLER CAMPAIGN NO 095.FOLDING FRONT SEAT BACK FITTED WITHSELF-LOCKINGLATCH WHICH HOLDS BACK OF SEAT IN UPRIGHT POSITION MAY NOT MEET REQUIREMENTSOF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO.207.PURPOSE OF LATCH IS TOMINIMIZE POSSIBILITYOF INJURY IN EVENT OF COLLISION.(CORRECT BY MAKINGNECESSARY ADJUSTMENTS. ) |
| Component | EQUIPMENT:MECHANICAL:INTEGRATED JACK/LEVELER/STABILIZER |
|---|---|
| Manufacturer | CHRYSLER CORPORATION |
| NHTSA Campaign ID | 70V103000 |
| Notes | POSSIBILITY THAT BUMPER JACK HOOK UNDER SOME CONDITIONS MAY NOT PROPERLY ENGAGELOWER EDGE OF REAR BUMPER DUE TO URETHANE COVERING ON BUMPER.IF IMPROPERENGAGE- MENT OF HOOK OCCURS IT COULD ALLOW VEHICLE TO FALL DURING JACKINGOPERATION.(CORRECT BY REPLACING HOOK WITH IMPROVED BUMPER HOOK.) |
| Component | SEATS:FRONT ASSEMBLY:RECLINER |
|---|---|
| Manufacturer | CHRYSLER CORPORATION |
| NHTSA Campaign ID | 69V127000 |
| Notes | POSSIBILITY THAT LEFT HAND SEAT BACK LATCH MAY FAIL TO LOCK AFTER REPEATEDLATCHINGS.IF THIS CONDITION EXISTS SEAT LOCK WILL NOT MEET MOTOR VEHICLESAFETY STANDARD NO.207.(CORRECT BY INSTALLING NEW IMPROVED SEAT BACK LATCH.) |
| Component | POWER TRAIN |
|---|---|
| Manufacturer | CHRYSLER CORPORATION |
| NHTSA Campaign ID | 69V163000 |
| Notes | POSSIBILITY THAT IMPROPER AXLE WAS INSTALLED IN ASSEMBLY, WHICH RE- SULTED INWRONG SPEEDOMETER PINION APPLICATION.(CORRECT BY INSTALLING THE PROPERSPEEDOMETER PINION GEAR TO AXLE RATIO.) |
| Component | EQUIPMENT:MECHANICAL:ACCESSORY SCISSOR/SCREW/BOTTLE JACK/LIFT |
|---|---|
| Manufacturer | CHRYSLER CORPORATION |
| NHTSA Campaign ID | 70V103000 |
| Notes | POSSIBILITY THAT BUMPER JACK HOOK UNDER SOME CONDITIONS MAY NOT PROPERLY ENGAGELOWER EDGE OF REAR BUMPER DUE TO URETHANE COVERING ON BUMPER.IF IMPROPERENGAGE- MENT OF HOOK OCCURS IT COULD ALLOW VEHICLE TO FALL DURING JACKINGOPERATION.(CORRECT BY REPLACING HOOK WITH IMPROVED BUMPER HOOK.) |
Data updated January 2023
1970 Plymouth Barracuda Recall FAQs (show)
Q: Does the 1970 Plymouth Barracuda have any vehicle recalls?
A: Yes, the 1970 Plymouth Barracuda has atleast 7 recalls.Q: What are the 1970 Plymouth Barracuda recalls?
A: The 1970 Plymouth Barracuda recalls include: WHEELS:RIM, POWER TRAIN:AXLE ASSEMBLY, SEATS:FRONT ASSEMBLY:RECLINER, EQUIPMENT:MECHANICAL:INTEGRATED JACK/LEVELER/STABILIZER, SEATS:FRONT ASSEMBLY:RECLINER, POWER TRAIN, EQUIPMENT:MECHANICAL:ACCESSORY SCISSOR/SCREW/BOTTLE JACK/LIFT.
A: Yes, the 1970 Plymouth Barracuda has atleast 7 recalls.Q: What are the 1970 Plymouth Barracuda recalls?
A: The 1970 Plymouth Barracuda recalls include: WHEELS:RIM, POWER TRAIN:AXLE ASSEMBLY, SEATS:FRONT ASSEMBLY:RECLINER, EQUIPMENT:MECHANICAL:INTEGRATED JACK/LEVELER/STABILIZER, SEATS:FRONT ASSEMBLY:RECLINER, POWER TRAIN, EQUIPMENT:MECHANICAL:ACCESSORY SCISSOR/SCREW/BOTTLE JACK/LIFT.