1967 Ford Bronco Specifications

These are standard specifications for the 1967 Ford Bronco, not necessarily specifications for the vehicle(s) in the photo(s).
Engine Location : Front
Drive Type : 4WD
Body / Chassis : Ladder frame
Production Years for Series : 1966 - 1977
Price : $2,194
Inline 6
Displacement : 3277 cc | 200.0 cu in. | 3.3 L.
Power : 120 BHP (88.32 KW) @ 4400 RPM
Bore : 3.7 in | 93 mm.
Stroke : 3.1 in | 80 mm.
Compression : 9.2:1
Main Bearings : 7
Valvetrain : 12 OHV (2 valves per cylinder)
Cylinder Block : Cast-iron
Holley 1-barrel carburetor
V 8
Displacement : 4556 cc | 278.0 cu in. | 4.6 L.
Power : 200 BHP (147.2 KW)
Bore : 4.0 in | 102 mm.
Stroke : 2.9 in | 73 mm.
Valvetrain : 16 OHV (2 valves per cylinder)
Transmission:
3 Manual Column shift

Total Ford Production for 1967 : 1,730,224
1967 Ford Bronco
Component

SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES

Manufacturer

FORD MOTOR COMPANY

NHTSA Campaign ID66V004003
NotesPOSSIBLE INTERFERENCE OF BRAKE PEDAL WITH THE DASH PANEL DRAIN TROUGH, PREVENTING FULL BRAKE PEDAL TRAVEL.SHOULD SUCH INTERFERENCE OCCUR IN CIRCUMSTANCES IN WHICH THE FRONT BRAKE SYSTEM IS NOT OPERATIVE, THE DUAL MASTER CYLINDER'S REAR BRAKING SYSTEM MAY BE RENDERED INOPERATIVE, TOO; OR REAR BRAKE SYSTEM EFFICIENCY MAY BE IMPAIRED.(REWORK THE DRAIN TROUGH.)

Component

STEERING:LINKAGES:DRAG:LINK:CONNECTION

Manufacturer

FORD MOTOR COMPANY

NHTSA Campaign ID66V026000
NotesPOSSIBILITY THAT INCORRECT STEERING DRAG LINK WAS USED IN ASSEMBLY.THIS COULD RESULT IN PREMATURE WEAR OF THE DRAG LINK BALL STUD AND OF THE ATTACHING HOLE IN THE PITMAN ARM.EXCESSIVE WEAR WILL RESULT IN PROGRESSIVELY GREATER STEERING EFFORT AND COULD EVENTUALLY CAUSE FAILURE AND COMPLETE LOSS OF STEER- ING CONTROL.(INSPECT AND REPLACE WITH CORRECT DRAG LINK AS NECESSARY.)

Information provided by NHTSA
Data updated June 2024
1967 Averages
Avg. Car Cost : $2,750
Avg. Household Income : $7,300
Avg. Home : $14,250
Avg. Gallon of Gas : $0.33

Popular frequently asked questions include:

What are the dimension and mechanical specifications of the 1967 Ford Bronco?
How many 1967 Ford Bronco were produced?
How powerful was the 1967 Ford Bronco? Was the 1967 Ford Bronco popular? Was the 1967 Ford Bronco expensive? What was the fuel economy of the 1967 Ford Bronco?

Q: What is the wheelbase size of the 1967 Ford Bronco? A: The 1967 Ford Bronco has a wheelbase size of 92.00 inches.

Q: What is the width of the 1967 Ford Bronco? A: The 1967 Ford Bronco has a width of 79.30 inches.

Q: How much did the 1967 Ford Bronco cost when new?A: The 1967 Ford Bronco had a base price of approximately $2,194 (USD).

Q: What is the bodystyle of the 1967 Ford Bronco? A: The 1967 Ford Bronco was a SUV.

Q: How many vehicles did Ford produce in 1967? A: Ford produced 1,730,224 automobiles in 1967.

Q: What engines did the 1967 Ford Bronco have? A: The 1967 Ford Bronco had the following engine options: Inline 6 (3277 cc | 200.0 cu in. | 3.3 L.) with 120 BHP (88.32 KW) @ 4400 RPM
  • V 8 (4556 cc | 278.0 cu in. | 4.6 L.) with 200 BHP (147.2 KW)
  • Q: What transmission did the 1967 Ford Bronco have? A: The 1967 Ford Bronco had a 3 speed Manual Column shift gearbox.

    Vehicle information, history, and specifications from concept to production.