conceptcarz.com

1920 Ford Model T Racer

Speedster

This Ford Model T track car, shown here in original condition, has a long competition history that includes laps at the famed Fairground Mile in Syracuse, New York. Syracuse hosted the first race in 1908. The racer is essentially a stock Model T fitted with a lightweight body and a modified engine. The combination of less weight and more power produced a car that could top 90 mph; braking from this speed with the stock brakes must have been dramatic. This vehicle is typical of race cars of the 1920s, which were often driven to and from the track.

by AACA Museum


Speedster

This is a one-of-a-kind hand-built race car, built by George Navarro and raced in California. It was found in a barn in Leesburg, VA. It has a top speed of 75 miles per hour and an average speed of nearly 60 miles per hour. After a mild restoration, it now is shown in parades and shows across the country, and it returned to racing in June of 2018 at the Indianapolis Motor Speedway, racing with 15 pre-1921 race cars in a four-day race.


Speedster

Without question, the Model 'T' Ford was the most popular vehicle ever produced for the world's motorists. From October 1, 1908, to May 31, 1927, 15 million came off the assembly lines.

Ford owners drove, raced, accessorized, cursed, cherished, and loved their cars. From the Indianapolis Motor Speedway, to Pike's Peak, to countless dirt tracks across the country, the Model 'T' based race cars left a legacy unmatched, unequaled, and unchallenged by any other production car in history.

The Model 'T' is the only car to have a medical ailment named for it 'The Ford Fracture' - a very special break to the right wrist caused by the improper use of the starting crank! On the lighter side, comedians got more laughs from jokes based on the Model T than any other car ever made.

For all its shortcomings, natural attrition, scrap metal drives and such, it's believed 1.5 million, fully 10-percent of Model Ts still exist today.

This example wears a two-seat racing body of unknown origin. It has a four-cylinder engine displacing 177 cubic inches and delivering 25 horsepower. There is a stock Planetary two-speed transmission, a modified Ford Model T steel frame, and mechanical expanding rear brakes - along with a transmission band brake with wire wheels.


Speedster

This chassis, known as the Ford Rajo Dirt Track Racer, has been driven by Erin West and Paul Russo and RC Linsey. Rajo Motor & Mfg. Company based in Racine Wisconsin built cylinder heads, designed by Joe Jagersberger, for Model 'T' cars. The company was named by combining the 'RA' from the city Racine and 'JO' from joe Jagersberger's first name.

On June 22, 2010, Tom Malloy purchased this car from Fausel Motorsports of la Quinta, CA. It is now part of Malloy Foundation, Inc., a private collection. It was on display for the 100 Anniversary of Corona Red race in 2013 and on display in City Hall for the 2016 Corona Road Race Celebration.

This vehicle is powered by a four-cylinder, 177 cubic-inch engine with 40 horsepower with Rajo overhead-valve conversion and Winfield model M carburetor. The maximum RPM is 3000. It has a Ford 2-speed, wire wheels, and rear disc brakes (which are not original).


Speedster

Without question, the Model 'T' Ford was the most popular vehicle ever produced for the world's motorists. From October 1, 1908 to May 31, 1927, 15 million came off the assembly lines.

As racing became more popular in the late teens, many small towns would use horse race tracks at local fairgrounds for automobile racing. In some cases, the tracks were for car racing exclusively. These were very exciting races and made it possible for local competitors to try their hand at winning the big prize money. This car is an example of that type of racer seen at oval race tracks all across the United States.

This 1920 Ford racer has a two-seat racing body and is powered by a 177 cubic-inch four-cylinder engine paired with a two-speed planetary transmission with a 3 speed Warford and 2 speed Ruckstell ear axle (12 forward speeds)! It has a Ford Model T steel frame, mechanical expanding rear brakes, transmission band brake, and Rocky Mountain aux brakes with wood wheels.


Speedster

The first board track for motor racing was the circular Los Angeles Motordrome, built in 1910 in the area that would later become the city's Playa del Rey district. Based on the same technology as European velodromes used for bicycle racing, this track and others like it were constructed with 2-inch x 4-inch boards, often with turns banked at up to 45 degrees. In some cases, such as the track at Culver City, banking was 50 degrees or more. Longer tracks were later built - some up to 2 miles long by 1915 - and lap speeds exceeding 100 miles per hour became commonplace.

Interest in motorsports was exploding during this period and by 1929, at least 24 board tracks had been built around the country, although by 1931, 20 of the 24 had been shut-down or abandoned, and from 1932 on, there were no more championship-level races run on boards. The tracks were relatively inexpensive to construct compared to more permanent facilities - the total facility cost of the 2-mile Tacoma Speedway was just $100,000 in 1915, compared to the $700,000 spent in 1909 just to pave the 2.5-mile Indianapolis Motor Speedway.

This 1920 Ford Board Track Racer has a lightweight single seat race car body and is powered by a 177 cubic-inch four-cylinder engine with Rajo overhead valve conversion. It has a stock planetary 2-speed transmission with Warford 3 speed auxiliary transmission and Ruckstell 2 speed rear end. It has a Ford Model T steel frame, wire wheels, and mechanical rear brakes and transmission brake.


The Ford Model T has an extensive history in the automotive market lasting for nearly 20 years. It is often called the 'Tin Lizzie' and the 'Flivver' and is credited with 'putting America on wheels.' During the early 1900's, the automobile was very new and the marketplace was adjusting to having these horseless carriages carry its passengers rather than bicycles or horses. Steam, electricity, and gasoline were the three means of powering the vehicles. Up until about 1915, no one really knew which would be the favorable power-source. Steam provided many benefits such as being quiet, clean, and cheap. Gasoline or kerosene fuel was used to heat water in a boiler; the steam produced was channeled to the cylinders, where the pressure drives the pistons up and down. The shortcomings were that it took a while to start, having to wait for the steam to prepare. It was dangerous, often exploding and causing injury. It had a limited range, lasting about 20-40 miles before requiring refueling. Electricity was popular but it too had a limited range. It was easy to start and was very popular with the ladies for driving around town. Then there was gasoline, which was dirty and hard to start. It required fueling stations that were sometimes difficult to find in this new and evolving marketplace. The main benefit of the gasoline engine was that it had the most potential and an ever-increasing amount of power. It was said that how a vehicle finished on the race track often determined the success of sales. With gasoline engines winning most of the races, the other sources of power were eventually doomed.

There were over 200 automobile manufacturers during the early 1900's. The average production figures for a factory were a couple of hundred vehicles a year. This, of course, varied greatly due to the complexity and prestige of the vehicle being produced. Henry Ford, the founder of the Ford Motor Company, produced a vehicle that was affordable but, more importantly, mass-produced. By using an assembly line to construct parts, rather than the traditional hand assembly, the process was streamlined. Using an assembly line process was not new, it had been done before in the meatpacking industry. William C. Klan had visited a slaughterhouse in Chicago. Upon returning from his visit, he proposed the idea to Peter Martin. A team was assembled and perfected through trial and error. The assembly line did not begin operation on the Model T until 1914. The assembly line process streamlined the production greatly, now averaging just over 90 minutes to assemble a car. During 1914, there were more Ford's produced than all other manufacturers combined. At that point 'you get it in any color you wanted so long as it was black'. Henry Ford favored the black color because it dried the fastest. During the years 1917 through 1923, Ford did not do any advertising, with 9 out of 10 cars being Ford, none was necessary.

He paid his workers a wage proportionate to the cost of the automobile, so they would be able to buy what they produced. By introducing these innovations, his factories were able to out-produce and outsell the rest of the industry and mobilize the country. When production of the Model T began, the cost was around $850, around $1200 less than most cars. By the early 1920's, the price of the Model T cost about $300. Ford had found many ways to cut costs and offer the least expensive product. He instructed his suppliers on how to assemble the wood crates that were used to ship him parts. The crates were then dismantled and used within the bodies of the car. The scrapes were made into charcoal and sold under the name 'Kingsford'.

The first Model T was produced on September 27th, 1908, at the Piquette Plant in Detroit, Michigan. There are two classes of the Model T, those that were produced before 1919 and after 1919. The pre-1919 Model T's are known as veteran cars, while the later models are called vintage cars. Even though the name Model T was used for almost twenty years, it was much improved both visually and mechanically over the years. At all times, the vehicle could be had in a wide variety of body styles. The open touring cars and roadsters were cheaper to produce and thus, built in greater numbers. The Volkswagen 'Beetle' is the only car model to outsell the Model T Ford.

The Model T was designed by Henry Ford, Childe Harold Wills, Joseph A. Galamb, and Eugene Farkas. A 177 cubic-inch four-cylinder motor was placed in the front and powered the rear wheels. The 20 horsepower engine was capable of carrying the vehicle to a top speed of around 45 mph. There were three main bearings and side valves. A ten-gallon fuel tank could be found beneath the front seat, mounted to the frame. The engine started by a hand crank located at the front of the vehicle. The crank was very difficult to operate and has been the cause of many broken arms.

The smaller engines were favored by Henry Ford. His Model K had used a six-cylinder engine, but when production ceased around 1908, Ford would not use a six-cylinder engine again until 1941. The Model K had not been a sales success. While Ford had wanted to produce small and inexpensive vehicles, his board of directors had persuaded him to produce a larger, luxurious, and expensive model. In 1906, Henry Ford purchased the majority of stock, leaving him in control and in charge of the direction of the company. After World War I, he purchased the remaining Ford stock so he could dispense with the board of directors entirely. From 1906 through 1908, Ford created the Model N, R, and S which eventually evolved into the Model T.

A 'three speed' planetary gear type transmission was used. This had been used in the Model K but was not suited to such a large vehicle. As a result, it suffered from frequent breakdowns but worked fine in the Model T. The 3-speed unit was actually two-speeds forward plus one reverse. With no clutch pedal, shifting was handled by floor pedals that did not require a clutch. Also located on the floor was a third pedal that operated the reverse gear. The throttle was controlled by a lever on the steering column. Neutral was located by the parking brake lever. The other foot pedal applied a band around a drum in the transmission. The parking brake lever operated the band brakes on the outside of the rear brake drums. When the hand lever was pulled back, the brake was engaged and the drive gears were disengaged.

Wooden 'artillery wheels' were standard until 1926 when they were replaced with steel wire wheels. The suspension was a transversely mounted semi-elliptical spring for both the front and rear axles. Brass was used throughout the earlier vehicles for items such as horns, radiators, and headlights. Headlights were acetylene lamps but later switched to electric lights.

Sales peaked in 1924, and over 2 million automobiles left the assembly line. By this time, many of Ford's competitors had switched to the same principles that had made the Model T successful: a cheap and reliable vehicle built on an assembly line produced in mass quantities. Other manufacturers started attracting new buyers by offering amenities, extras, or larger engines. Popular options included windshield wipers, anti-theft locks, and light dimmers. Chevrolet vehicles had three forward gears, while the Model T still used only two. Also, since the Model T's were so durable, they were still in functioning order. This means that many owners did not need a car, and when they did, they usually bought a more luxurious vehicle. The used Model T's were then sold for next to nothing. Sales began to dip in 1925 and dramatically in 1926. Production ceased in 1927 for nearly six months while preparations were made for the production of the Model A.

The Model T mobilized a nation, not only the United States but many other countries. With dealerships and factories set up throughout the world, the Model T was mass-produced and easily available to many buyers. Often, the factories were established in other countries to get around an import tax, thus keeping the cost low. The innovative Model T served its purpose. It was inexpensive and reliable, many lasting even to this day.

by Dan Vaughan