These are standard specifications for the 1967 Dodge Charger, not necessarily specifications for the vehicle(s) in the photo(s).
Transmission:
3 Manual , 4 Manual , 3 Automatic TorqueFlite
Information provided by NHTSA
Data updated January 2023
Features
Engine Location : | Front |
Drive Type : | Rear Wheel |
Production Years for Series : | 1966 - 1967 |
Price : | $3,130 |
Weight : | 3480 lbs | 1578.501 kg |
Engine & Transmission
V 8 | |
---|---|
Displacement : | 5211 cc | 318.0 cu in. | 5.2 L. |
Power : | 230 BHP (169.28 KW) @ 4400 RPM |
Bore : | 3.9 in | 99 mm. |
Stroke : | 3.3 in | 84 mm. |
Compression : | 9.0:1 |
Main Bearings : | 5 |
Stromberg 2-barrel WW3-258 carburetor |
V 8 | |
---|---|
Displacement : | 6981 cc | 426.0 cu in. | 7.0 L. |
Power : | 425 BHP (312.8 KW) @ 5600 RPM |
Bore : | 4.3 in | 108 mm. |
Stroke : | 3.8 in | 95 mm. |
Compression : | 10.25:1 |
Main Bearings : | 5 |
Valvetrain : | 16 OHV (2 valves per cylinder) |
Cylinder Block : | Cast-iron |
2 Carter AFB-3084S 4-barrel carburetor |
3 Manual , 4 Manual , 3 Automatic TorqueFlite
Production Figures
Total Dodge Production for 1967 : | 465,732 |
Total 1967 Charger production : | 15,788 |
1967 Dodge Charger | |
Hardtop Coupe 2 dr. 6 P : | 15,788 |
Dimension(s)
Hardtop Coupe
Seating Capacity : | 6 |
Doors : | 2 |
Exterior | |
---|---|
Length : | 203.0 in | 5156 mm. |
Wheelbase : | 117.0 in | 2972 mm. |
Handling
Recall
Component | SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC |
---|---|
Manufacturer | CHRYSLER CORPORATION |
NHTSA Campaign ID | 67V062000 |
Notes | POSSIBLE THAT, UNDER CERTAIN CONDITIONS, WATER MAY ENTER THE DISC BRAKE PROPORTIONING VALVE VENT.INTERNAL SEAL DAMAGE CAUSED BY CORROSION INSIDE THE VALVE COULD RESULT IN FLUID LEAKAGE.PROLONGED OR SEVERE LEAKAGE WILL AFFECT NORMAL BRAKING OPERATION ON 1966 MODELS AND CAUSE LOSS OF EFFECTIVENESS ON REAR WHEEL PORTION OF 1967 DUAL BRAKE SYSTEM.(REPLACE THE SUBJECT PROPORTIONING VALVE.) |
Component | WHEELS:MULTI PIECE |
---|---|
Manufacturer | CHRYSLER CORPORATION |
NHTSA Campaign ID | 67V064000 |
Notes | POSSIBLE THAT VEHICLES WERE ASSEMBLED WITHOUT FRONT WHEEL HUB DUST CAPS.OMISSION OF THE DUST CAPS WILL SUBJECT THE FRONT WHEEL BEARINGS TO ROAD DIRT, WATER, CORROSIVE SALT, ETC.THIS CONDITION COULD RESULT IN EARLY BEARING FAILURE.(INSPECT, REPLACE BEARINGS IF NECESSARY, AND INSTALL DUST CAPS.) |
Component | ELECTRICAL SYSTEM:IGNITION |
---|---|
Manufacturer | CHRYSLER CORPORATION |
NHTSA Campaign ID | 67V009003 |
Notes | POSSIBLE INTERFERENCE BETWEEN THE STARTER CABLE AND THE STEERING SHAFT LOWER BEARING COLLAR SET SCREW.THIS MAY CAUSE A POSSIBLE INTERFERENCE WITH THE STEERING SYSTEM, RESULTING IN RESTRICTED VEHICLE CONTROL, OR AN ELECTRICALSHORT CIRCUIT RESULTING IN COMPLETE FAILURE OF THE ELECTRICAL SYSTEM.(INSPECT AND CORRECT MISLOCATED CYLINDER HEAD STARTER CABLE CLIP, WHICH PERMITTED INTERFERENCE, AS NECESSARY.) |
Data updated January 2023
1967 Averages
Avg. Car Cost : | $2,750 |
Avg. Household Income : | $7,300 |
Avg. Home : | $14,250 |
Avg. Gallon of Gas : | $0.33 |
1967 Dodge Charger FAQs (show)
Popular frequently asked questions include:
What are the dimension and mechanical specifications of the 1967 Dodge Charger?
Q: What is the wheelbase size of the 1967 Dodge Charger? A: The 1967 Dodge Charger has a wheelbase size of 117.00 inches.Q: What is the length of the 1967 Dodge Charger? A: The 1967 Dodge Charger has a length of 203.00 inches.Q: How much did the 1967 Dodge Charger cost when new?A: The 1967 Dodge Charger had a base price of approximately $3,130 (USD).Q: What is the bodystyle of the 1967 Dodge Charger? A: The 1967 Dodge Charger was a Hardtop Coupe.Q: How many vehicles did Dodge produce in 1967? A: Dodge produced 465,732 automobiles in 1967.Q: How many 1967 Chargers were produced? A: Dodge produced 15,788 examples of the Charger in 1967.Q: What engines did the 1967 Dodge Charger have? A: The 1967 Dodge Charger had the following engine options: V 8 (5211 cc | 318.0 cu in. | 5.2 L.) with 230 BHP (169.28 KW) @ 4400 RPM V 8 (6981 cc | 426.0 cu in. | 7.0 L.) with 425 BHP (312.8 KW) @ 5600 RPM Q: What transmissions did the 1967 Dodge Charger have? A: The 1967 Dodge Charger had the following gearbox options: 3 speed Manual, 4 speed Manual, 3 speed Automatic TorqueFlite.
What are the dimension and mechanical specifications of the 1967 Dodge Charger?
How many 1967 Dodge Charger were produced?
How powerful was the 1967 Dodge Charger? Was the 1967 Dodge Charger popular? Was the 1967 Dodge Charger expensive? What was the fuel economy of the 1967 Dodge Charger?
Q: What is the wheelbase size of the 1967 Dodge Charger? A: The 1967 Dodge Charger has a wheelbase size of 117.00 inches.Q: What is the length of the 1967 Dodge Charger? A: The 1967 Dodge Charger has a length of 203.00 inches.Q: How much did the 1967 Dodge Charger cost when new?A: The 1967 Dodge Charger had a base price of approximately $3,130 (USD).Q: What is the bodystyle of the 1967 Dodge Charger? A: The 1967 Dodge Charger was a Hardtop Coupe.Q: How many vehicles did Dodge produce in 1967? A: Dodge produced 465,732 automobiles in 1967.Q: How many 1967 Chargers were produced? A: Dodge produced 15,788 examples of the Charger in 1967.Q: What engines did the 1967 Dodge Charger have? A: The 1967 Dodge Charger had the following engine options: V 8 (5211 cc | 318.0 cu in. | 5.2 L.) with 230 BHP (169.28 KW) @ 4400 RPMSimilar Vehicles
Similarly Sized Vehicles
from 1967
Similarly Priced Vehicles
Dodge Monthly Sales Volume
March 2023
50,975