1980 Buick Skylark Specifications

Article

Image gallery

Specifications

Features

Engine Location :	Front
Drive Type :	Front Wheel
Body / Chassis :	Unitized Body Construction
Production Years for Series :	1980 - 1985
Price :	$5,160-$5,925
Weight :	2415 lbs \| 1095.426 kg

Engine & Transmission

Inline 4
Displacement :	2474 cc \| 151.0 cu in. \| 2.5 L.
Power :	90 HP (66.24 KW) @ 4000 RPM
Torque :	134 Ft-Lbs (182 NM) @ 2400 RPM
Bore :	4.0 in \| 102 mm.
Stroke :	3.0 in \| 76 mm.
Compression :	8.2:1
Main Bearings :	5
Construction :	Cast-iron block and head
Rochester 2-barrel carburetor

V 6
Displacement :	2835 cc \| 173.0 cu in. \| 2.8 L.
Power :	115 HP (84.64 KW) @ 4800 RPM
Torque :	145 Ft-Lbs (197 NM) @ 2400 RPM
Bore :	3.8 in \| 97 mm.
Stroke :	3.4 in \| 86 mm.
Compression :	8.5:1
Main Bearings :	4
Construction :	Cast-Iron Alloy block and head
Rochester 2-barrel carburetor

Transmission:
4 Manual Fully synchronized , Automatic

Gear Ratios

1st Gear :	3.53:1
2nd Gear :	1.95:1
3rd Gear :	1.24:1
4th Gear :	0.81:1

Production Figures

Total Buick Production for 1980 :	854,011
1980 Buick Skylark
Coupe 2 dr. 5 P :	55,114
Limited Coupe 2 dr. 5 P :	42,652
Limited Sedan 4 dr. 5 P :	86,948
Sedan 4 dr. 5 P :	80,940

Handling

Recall

Component	FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
Manufacturer	GENERAL MOTORS CORP.
Mfr Report Date	19780801
NHTSA Campaign ID	79V091000
Summary	FUEL HOSES MAY BE INCORRECTLY POSITIONED AND CONTACT THE RIGHT FRONT DRIVE AXLE BOOT DURING VEHICLE OPERATION. AFTER A PERIOD OF TIME, THE ROTATING BOOT COULD WEAR A HOLE IN THE FUEL HOSE, RESULTING IN FULE LEAKAGE.
Remedy	IF PROPER CLEARANCE IS NOT PRESENT, THE METAL FUEL PIPE WILL BE REFORMED UPWARDS TO CORRECT THE PROBLEM, WITHOUT CHARGE TO OWNER.
Notes	VEHICLE DESCRIPTION: PASSENGER VEHICLES.SYSTEM: FUEL; FUEL HOSE.CONSEQUENCES OF DEFECT: LEAKING FUEL COULD LEAD TO A FIRE IN THE ENGINECOMPARTMENT, VEHICLE DAMAGE, AND PERSONAL INJURY TO PASSENGERS.

Component	SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS
Manufacturer	GENERAL MOTORS CORP.
Mfr Report Date	19780801
NHTSA Campaign ID	79V090000
Summary	THERE IS A POTENTIAL FOR INTERFERENCE BETWEEN THE CLUTCH CONTROL CABLE AND BRAKE PIPE IN THE MASTER CYLINDER. THIS CAN RESULT IN RUBBING CONTACT WHEN THE CLUTCH PEDAL IS OPERATED. ALSO, THE BRAKE PIPE CLEARANCE TO THE TRANSMISSION CASE MAY BE INADEQUATE. IF THIS CONDITION EXISTS, IT COULD EVENTUALLY RESULT IN A FAILURE IN THE BRAKE PIPE, CAUSING LOSS OF BRAKE FLUID AND PARTIAL LOSS OF BRAKING ACTION.
Remedy	THE CLUTCH CABLE ROUTING WILL BE REVISED TO PREVENT CONTACT WITH THE MASTER CYLINDER, WITHOUT CHARGE.
Notes	VEHICLE DESCRIPTION: PASSENGER VEHICLES.SYSTEM: POWER TRAIN; CLUTCH ASSEMBLY.CONSEQUENCES OF DEFECT: SHOULD A PARTIAL LOSS OF BRAKING ACTION OCCUR WHILE THEVEHICLE IS IN MOTION AT A TIME WHEN MINIMUM STOPING DISTANCE IS REQUIRED, ANACCIDENT WOULD RESULT.

Component	SUSPENSION:FRONT:SPRINGS:COIL SPRINGS
Manufacturer	GENERAL MOTORS CORP.
Mfr Report Date	19780801
NHTSA Campaign ID	79V098000
Summary	THE FRONT SUSPENSION COIL SPRING MAY HAVE A LARGER THAN DESIRED INSIDE DIAMETER OF THE LOWER COIL WHERE IT RESTS ON THE SPRING SEAT. THIS COULD ALLOW THE SPRING TO BE FORCED OVER THE LOWER SPRING SEAT DUE TO SUSPENSION FORCES.
Remedy	DEALER WILL INSPECT AND REPLACE INCORRECT FRONT SUSPENSION COIL SPRINGS WITHOUT CHARGE.
Notes	VEHICLE DESCRIPTION: PASSENGER VEHICLES.SYSTEM: SUSPENSION; FRONT COIL.CONSEQUENCES OF DEFECT: THIS CONDITION WOULD CAUSE BRAKE HOSE AND SUSPENSIONDAMAGE. TIRE DAMAGE MAY ALSO OCCUR WITH CONTINUED VEHICLE OPERATION. DAMAGE TOANY OF THESE COMPONENTS COULD CAUSE LOSS OF VEHICLE CONTROL AND AN ACCIDENT.

Component	SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DIFFERENTIAL PROPORTIONAL VALVE
Manufacturer	GENERAL MOTORS CORP.
Mfr Report Date	19780801
NHTSA Campaign ID	81V095000
Summary	UNDER CERTAIN CONDITIONS, THE REAR BRAKES COULD LOCK UP WITHOUT PRIOR WARNING DURING HIGH DECELERATION BRAKING. THE PROBLEM MAY BE CAUSED BY DEFECTIVE PROPORTIONER VALVES IN THE BRAKING SYSTEM.
Remedy	THE DEALER WILL INSPECT THE BRAKE SYSTEM PROPORTIONER VALVES AND IF NECESSARY INSTALL NEW VALVES.
Notes	VEHICLE DESCRIPTION: PASSENGER VEHICLES WITH MANUAL TRANSMISSIONS.SYSTEM: SERVICE BRAKES; REAR BRAKES.CONSEQUENCES OF DEFECT: REAR BRAKE LOCKUP COULD CAUSE A LOSS OF VEHICLE CONTROLAND AN ACCIDENT.

Component	SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS
Manufacturer	GENERAL MOTORS CORP.
Mfr Report Date	19790101
NHTSA Campaign ID	83V018000
Summary	UNDER CERTAIN CONDITIONS, VEHICLES MAY EXPERIENCE PREMATURE REAR WHEEL SKID DURING BRAKING. REAR WHEEL SKIDDING IS MOST LIKELY TO OCCUR ON A WET OR SLICK SURFACE.
Remedy	DEPENDING ON THE TRANSMISSION TYPE AND THE BRAKE COMPONENTS THAT HAVE BEEN INSTALLED, DEALERS WILL INSPECT AND REPLACE OR REPAIR, AS NECESSARY, CERTAIN FRONT BRAKE COMPONENTS, AND THE PARKING BRAKE CABLES. THE REAR BRAKE SHOES AND LININGS WILL BE REPLACED WITH PARTS THAT USE A MATERIAL WHICH GREATLY REDUCES THE LIKELIHOOD OF REAR WHEEL SKID. ACTIONS TAKEN TO THE FRONT BRAKES ARE TO ENSURE UNIFORMITY OF THE ENTIRE BRAKE SYSTEM. ACTIONS TAKEN TO THE PARKING BRAKE COMPONENTS WILL ENSURE THAT THE PERFORMANCE REQUIREMENTS, FOR KEEPING THE VEHICLE STATIONARY WHILE MANUAL TRANSMISSION EQUIPPED UNITS ARE IN NEUTRAL AND AUTOMATIC TRANSMISSION EQUIPPED UNITS ARE IN PARK, ARE MET.
Notes	VEHICLE DESCRIPTION: PASSENGER VEHICLES.SYSTEM: SERVICE BRAKES; REAR BRAKES.CONSEQUENCES OF DEFECT: IF THE DRIVER IS UNABLE TO COMPLETE CORRECTIVE STEERINGOR BRAKING ACTIONS, THE REAR END OF THE VEHICLE MAY SKID OUT OF ITS LANE OFTRAVEL, POSSIBLY RESULTING IN AN ACCIDENT.NOTE: UNTIL THE PROBLEM IS CORRECTED, THE DRIVER SHOULD USE CAUTION IN MAKINGHARD BRAKING STOPS.

Component	SEATS
Manufacturer	GENERAL MOTORS CORP.
Mfr Report Date	19790101
NHTSA Campaign ID	79V073000
Summary	VEHICLES DO NOT COMPLY TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, 'ANCHORAGE OF SEATS'. THE LOCK BAR IN THE FRONT SEAT ADJUSTER ASSEMBLIES MAY NOT ENGAGE PROPERLY AND THE ABILITY OF THE SEAT ADJUSTER TO MAINTAIN THE SEAT IN A LATCHED POSITION DURING AN ACCIDENT MAY BE REDUCED.
Remedy	BOTH FRONT SEAT ADJUSTER ASSEMBLIES WILL BE REPLACED AT NO CHARGE TO OWNER.
Notes	VEHICLE DESCRIPTION: PASSENGER VEHICLES.SYSTEM: INTERIOR; FRONT SEAT ADJUSTER ASSEMBLY.CONSEQUENCES OF DEFECT: IN THE EVENT OF AN ACCIDENT, THE RISK OF INJURY TOPASSENGERS WILL BE INCREASED.

Component	EXTERIOR LIGHTING:TURN SIGNAL:FLASHER UNIT
Manufacturer	GENERAL MOTORS CORP.
Mfr Report Date	19790101
NHTSA Campaign ID	79V234000
Summary	THE TURN SIGNAL FLASHER UNIT INSTALLED ON THE INVOLVED VEHICLES FAILS TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, 'LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT'. THIS INCORRECT UNIT CAUSES THE FLASH RATE TO BE TOO FAST OR RENDERS INOPERATIVE THE FEATURE WHICH CAUSES THE TURN SIGNAL INDICATOR LIGHT(S) IN THE INSTRUMENT PANEL TO REMAIN LIT IF ONE OF ONE OR MORE OF THE TURN SIGNAL LIGHTS HAS FAILED.
Remedy	DEALER WILL INSTALL THE CORRECT FLASHER UNIT WITHOUT CHARGE TO OWNER.
Notes	VEHICLE DESCRIPTION: PASSENGER VEHICLES.SYSTEM: LIGHTING AND COMMUNICATIONS; FLASHER, TURN SIGNALS.CONSEQUENCES OF DEFECT: INOPERATIVE OR MALFUNCTIONING TURN SIGNAL CREATES ANUNSAFE CONDITION THAT COULD LEAD TO A VEHICLE ACCIDENT.

Component	STEERING:RACK AND PINION
Manufacturer	GENERAL MOTORS CORP.
Mfr Report Date	19790101
NHTSA Campaign ID	79V221000
Summary	THE STEERING GEAR MOUNTING PLATE ON THE INVOLVED VEHICLES MAY DEVELOP FATIGUE CRACKS AT HIGH MILEAGE WHICH WOULD ALLOW THE STEERING GEAR ATTACHMENT TO BECOME LOOSE. IF THIS CONDITION EXISTS, THE DRIVER MAY NOTICE CONSIDERABLE 'FREE PLAY' IN THE STEERING WHEEL.
Remedy	THE DEALER WILL INSTALL AN IMPROVED TYPE OF STEERING GEAR MOUNTING BRACKET WITHOUT CHARGE TO OWNER.
Notes	VEHICLE DESCRIPTION: PASSENGER VEHICLES.SYSTEM: STEERING; GEAR MOUNTING BRACKET.CONSEQUENCES OF DEFECT: THIS CONDITION MAY RESULT IN DEGRADATION OF STEERINGCONTROL, WHICH COULD LEAD TO LOSS OF VEHICLE CONTROL AND AN ACCIDENT.

Component	POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES
Manufacturer	GENERAL MOTORS CORP.
Mfr Report Date	19790101
NHTSA Campaign ID	79V220000
Summary	THE AUTOMATIC COOLER LINE HOSES ON SOME OF THE SUSPECT VEHICLES MAY CONTAIN MATERIAL VOIDS, WHICH COMBINED WITH A HIGH THERMAL EXPANSION AT ELEVATED TEMPERATURES, COULD RESULT IN HOSE FAILURE AND TRANSMISSION FLUID LEAKAGE.
Remedy	THE DEALER WILL REPLACE THE COOLER LINE HOSES USING HOSES WITH KEVLAR BRAIDED REINFORCEMENT.
Notes	VEHICLE DESCRIPTION: PASSENGER VEHICLES.SYSTEM: POWER TRAIN; TRANSMISSION HOSES.CONSEQUENCES OF DEFECT: A VEHICLE FIRE MAY RESULT WHICH COULD CAUSE SERIOUSPERSONAL INJURY.

Information provided by NHTSA
Data updated June 2024

1980 Averages

Avg. Car Cost :	$7,210
Avg. Household Income :	$19,170
Avg. Home :	$68,714
Avg. Gallon of Gas :	$1.22
Total Car Production :	8,009,841

1980 Buick Skylark FAQs (show)

Popular frequently asked questions include:

What are the dimension and mechanical specifications of the 1980 Buick Skylark?
How many 1980 Buick Skylark were produced?
How powerful was the 1980 Buick Skylark? Was the 1980 Buick Skylark popular? Was the 1980 Buick Skylark expensive? What was the fuel economy of the 1980 Buick Skylark?

Q: What is the wheelbase size of the 1980 Buick Skylark? A: The 1980 Buick Skylark has a wheelbase size of 104.90 inches.

Q: What is the length of the 1980 Buick Skylark? A: The 1980 Buick Skylark has a length of 181.90 inches.

Q: What is the width of the 1980 Buick Skylark? A: The 1980 Buick Skylark has a width of 67.70 inches.

Q: How much did the 1980 Buick Skylark cost when new?A: The 1980 Buick Skylark cost approximately $5,160 to $5,925 (USD) when new.

Q: What were the bodystyles of the 1980 Buick Skylark? A: The 1980 Buick Skylark was offered as a Coupe, Limited Coupe, Limited Sedan, Sedan, Sport Coupe, Sport Sedan.

Q: How many vehicles did Buick produce in 1980? A: Buick produced 854,011 automobiles in 1980.

Q: What engines did the 1980 Buick Skylark have? A: The 1980 Buick Skylark had the following engine options: Inline 4 (2474 cc | 151.0 cu in. | 2.5 L.) with 90 HP (66.24 KW) @ 4000 RPM and 134 Ft-Lbs (182 NM) @ 2400 RPM

V 6 (2835 cc | 173.0 cu in. | 2.8 L.) with 115 HP (84.64 KW) @ 4800 RPM and 145 Ft-Lbs (197 NM) @ 2400 RPM

Q: What transmissions did the 1980 Buick Skylark have? A: The 1980 Buick Skylark had the following gearbox options: 4 speed Manual Fully synchronized, Automatic.